Liquid >> Single / Twin Head weight Filler - Tin/Jerry can 5kg -30 kg JDL Series
The JDF series of weight-controlled filling systems provides accurate filling to the Department of Trade and industry standards for containers in the range of 10 to 200 liters and above. Weighing systems integrated with the filling machine are suitable for installation in wash down, hazardous and other hostile environments. Operator safety and efficient fulfillment of production requirements are paramount.
Most suitable for a wide range of liquids that vary widely in viscosity and foaming characteristics. The range includes bung-entry filling for non-foaming products, submerged filling for foaming and hazardous products. Filling can be in single drum including depalletising, palletizing, debunging , bunging , oversealling, environmental control enclosures, automatic weight checking , computer control, data management , etc.
It is fully microprocessor controlled and contained many sophisticated functions to fill drums to desired weight accurately and efficiently. Designed to fill directly from supply pump and coupled with pressure requlator that activate near the target weight, it fully ensure a clean and spillage free operation with last drops collected by the automatic drip tray.
Most suitable for a wide range of liquids that vary widely in viscosity and foaming characteristics. The range includes bung-entry filling for non-foaming products, submerged filling for foaming and hazardous products. Filling can be in single drum including depalletising, palletizing, debunging , bunging , oversealling, environmental control enclosures, automatic weight checking , computer control, data management , etc.
It is fully microprocessor controlled and contained many sophisticated functions to fill drums to desired weight accurately and efficiently. Designed to fill directly from supply pump and coupled with pressure requlator that activate near the target weight, it fully ensure a clean and spillage free operation with last drops collected by the automatic drip tray.
STANDARD FEATURES
For open top drums and drums with bungholes
Three stages coarse/medium/fine fill
Three modes MANUAL/NET/GROSS fill
Auto –adjust NET fill and no tare GROSS fill
Zero point check ensuring no drum clamp assembly
Below level filling for good accuracy
Non – drip nozzle and automatic drip tray
Overfill protection and spillage free with pressure regulator
Automatic nozzle rise and fall system
Emergency stop to halt product flow
Auto shut off and fail safe on power failure
Automatic bung alignment protection
Premature ascent interlock, to prevent the filling head withdrawing from the drum before the fill cycle is completed
Stainless steel construction and PTFE material on all wetted parts
Heavy duty gravity roller conveyor on scale platform
OPERATING SPEED
90 drums per hour for 210 litre drum based on water at 2kg/sq cm and 30 cu.m/hr.
60 to 75 drums per hour depending on product .
SCALE CAPACITY/ACCURACY
0-300KG X 0.1KGTare: up to 300KG
Scale display accuracy is +/-0.03 % with an internal accuracy of +/-01.01%.
LANCE AASEMBLY
304 stainless stell, 38mm OD, telfon foot valve seat.
PRESSURE REQULATOR
Pneumatically controlled flow control valve to control variation in product supply pressure, pneumatically controlled.
MICROPROCESSOR CONTROL SYSTEM
The electronic control system ensures accurate weighing process and also automatically controls the weight for each weighing. The weight valves can be output to external device for further data processing or recording.
MATERIAL
Parts in contact with the liquid are 304 stainless steel fluorosin, P.T.F.E. and PVC hose. All seals are chemical resistant packing seal.
PRODUCT PRESSURE FEED
Not exceeding 2.5kg.sq.cm
FINISH
Prime coat in red oxide ant-rust paint and finish with green apoxy powder paint.
NET WEIGHT
Approximately 400 kg.
AIR SUPPLY
6-7 kg/sq.cm at 0.2 cu.m/min, a filter-lubricator is provided
ELECTRICAL TEMPRATURE
-5 deg C to + 40 deg C.
OPTIONS
Entry and take away conveyor and tilting
Depalletising and palletising system
Labeling, coding and capping machines
Pre-fill station for performance improvement
Height-equalizing product hose suspension
316 stainless steel on all wetted parts
Gas enclosure hood
Explosion proof version
Management data systems.